Kiwi TJ
Just asked myself if I’m crazy and we all said No
Supporting Member
Ride of the Month Winner
Looks like you need to carry some Oreo cookies in your Jeep to stop you chewing on your clutch pedal
What did you do to your TJ today?
- Thread starter LJRubiconGuy
- Start date
Looks like you need to carry some Oreo cookies in your Jeep to stop you chewing on your clutch pedal
Looks like you need to carry some Oreo cookies in your Jeep to stop you chewing on your clutch pedal
I gets hungry out on the trail.
I replaced the O2 sensors and reset the code. Much better low end performance heading into work.
I'll check the mpg next. I bet it's up at least .25 mpg.
I'll check the mpg next. I bet it's up at least .25 mpg.
I replaced the O2 sensors and reset the code. Much better low end performance heading into work.
I'll check the mpg next. I bet it's up at least .25 mpg.
That should move you up to 42mpg. Maybe more
That should move you up to 42mpg. Maybe more
Doesn't he need the Fram oil filter too, for those gains?
My secret weapon for 43 mpg.
Hennep87
TJ Enthusiast
I replaced the O2 sensors and reset the code. Much better low end performance heading into work.
I'll check the mpg next. I bet it's up at least .25 mpg.
How do you reset the code?
I have a P0128 code.
- Changed temp sensor
- changed Thermostat
- Flushed the whole thing and put new coolant in there.
Check engine light is still on.
Drove it to work to make sure its running good and no CEL come one since I have a smog appointment friday
I have an older chorded and newer bluetooth code reader that resets codes.
It's that or pulling the battery cable.
It's that or pulling the battery cable.
Disconnect the negative battery cable for a couple of minutes. If the code comes back up in 24 hours, the problem wasn't fixed.
Hennep87
TJ Enthusiast
Yeah, that’s what I thought… it’s coming back after a few days after I disconnected the battery.
I was hoping I did something wrong “resetting it”
Got some Genright corner guards in and started today on the fitment!!.. yes I took off the corner guards… no I’m not selling them @SilverLJR
Front end Wednesday. Got my new raised winch plate and new to me rock crawler bumper all buttoned up. Good excuse to test the winch and retension the line, and I’ll see if I need to clearance the end of the plate so the soft shackles don’t rub.
New parking brake adjuster/balancer assy as the old one was a mass of rust, esp. on the adjustment bolt. I had to get out the "I'm not asking" tool to get the old one off...
Zataxx
New Member
Overkill makes me feel safer so a dedicated trailer hitch was the way to go for me.
Zataxx
New Member
Changed oil (casterol) and transmission oil (redline). Installed brute power fuel pump. Saved mopar fuel pump to rebuild with usa bosch motor i have. Checked gear teeth on speedometer, ordered new one. Removed some wiring and rear light from po. Put in new spark plugs. Replaced drivers side speaker cover that po put rocker switched in. Changed shift knob to a ball, old one missing center cap.
Busy day. Took off work just for this.
Busy day. Took off work just for this.
Removed my airbag switch since I've disabled them and put an aftermarket steering wheel on. It was tricky getting this to fit in the 2000 console.
Removed the MorRyde tailgate system and installed the Texas Jeep billet aluminum tailgate hinges. Also deleted the third brake light from the tailgate. I'm going to run to my rear cross bar and install a Rigid tail & chase light with the chase feature hooked to the parking lights.
If anyone wants the factory tailgate side third brake light wiring, I'll send it to you for the cost of postage.
Removed the MorRyde tailgate system and installed the Texas Jeep billet aluminum tailgate hinges. Also deleted the third brake light from the tailgate. I'm going to run to my rear cross bar and install a Rigid tail & chase light with the chase feature hooked to the parking lights.
If anyone wants the factory tailgate side third brake light wiring, I'll send it to you for the cost of postage.
I just ripped mine out, too! But it's in a ziploc on the shelf in case I ever change my mind. lol
Did you repaint or deep clean the dash? If repaint... How did you match the "khaki" color?
Similar threads
