dana 30

Hey guys first post here hoping someone can help me out. I have an Aussie locker in my front Dana 30 with 33x12.5 tires. When I’m driving in the snow down a straight road i hear a clunk noise and my car pulls hard to left for a couple seconds. It then goes away and drives straight perfectly fine...

I'm looking to upgrade my front and rear axles this year, and I am researching my options and would like to get allayall's opinions and advice on the front end. I am currently running a factory Dana 30/35 combo at 3.73 with ECGS chromoly axles in the 30. Will be upgrading to 35" tires on 15x8's...

There are two hub kits available for the Dana 30 from Yukon, the WU-07 and WU-08. Both are pretty spendy, 07 being just less than $1000, and the 08 right at $1450. I chose the 08 feeling it was a bit more robust hub unit, with the 07 being very similar to old Bronco II hub units. I have no real...

Hello! I’m looking for a Dana 44 front axle, this guy on FB Marketplace says he has a Dana 30 with the factory 4.10 gears from a 2004 sport, but they didn’t come with those gears, I’ve attached pictures. Could someone tell my by the picture if this is a Dana 30 or 44? If it’s a 44 then is it in good...

Oh, look, another LS conversion in a TJ. :rolleyes: Yes, this thread is about another conversion, but I hope to alleviate and answer alot of confusion and offer some answers or advice. The goal with "Sarah" is to have a capable DD that can be very capable on the weekend. This project has...

So I broke a passenger axle stub on my Michigan rusted out 98’ 4cyl Manual and luckily I have a friend with a bone yard. Stole a new stub from a 93 hoping they were the same as I read on the Internet... They aren’t. The u joint caps on my old one are bigger. However the part listings everywhere...

Hello! I recently came across a Jeep I found very interesting and took for a test drive. It was a 1999 Wrangler SE with a V8 Hemi motor. The thing that concerns me is that it still has the original axels that came with the 2.5L, the Dana 30 and 35s. Will this be a significant problem? Will those...

By chance, does anyone have CAD files/Scans of the TJ/LJ/XJ Dana 30 LP/HP, TJ/LJ Dana 44 LP, and or a Ford Dana 60 LP/HP and are willing to share? Any help would be appreciated. Looking to help further the development of some axle armor for us Jeep owners. Please do not share any copyrighted...

So my Jeep is currently on 33’s and id like to go to 35’s soon. My current setup in my 30 is stovk everything with a Spartan locker and 4.56 gears. I like to wheel my Jeep so i want to make it tough enough for 35’s. My current list would be a truss, probably from jcr some c-gussets and a set of...

Shooting for the moon with this one. But I am looking for a Dana 30 high pinion center section. Tubed or de-tubed; de-tubed is preferred. Would also prefer factory bearing caps in them as well. Wish me luck!

I'm trying to find Dana 30 and Dana 35 axle housings. Surprisingly, Davey's Jeeps doesn't carry just the housings. Any recommendations on where to find them besides craigslist and eBay?

Hi, Was wondering if I swapped out my rear Dana 30 diff and axles will a Dana 44 diff and axles bolt right in using the rest of the existing stuff on the car? Such as is the brakes, hubs, ball joints, Cs, knuckles, and steering the same? Thanks

Ok So I have a 06 Lj with 4.88 gears and a spartan locker (2years old) in my dana 30. Was wondering if anyone else had problems with this locker? or can tell me if the loud banging sound coming from my dana 30 is my locker. Ok so for a few months I knew my axle shaft u-joint was bad, but it...

What happens if you break a Dana 30 Axle Shaft when you are out wheeling? This question is related to some budget strategies/planning I am doing regarding axle/locker upgrades for my stock axles (Dana 30/Dana 35 on a 2001 TJ Sport). I think I know what happens if you break an axle shaft on a...

Current situation.. 2000, 2.5 motor, ax5 trans, 4.10 gears(open/open), believe it's a 4 or 4.5in pro comp lift kit, 32in tires. I have a Ford 9in (full width from 81 bronco) with limited slip sitting in my garage. Goal... Run 33-35in tires, locked, not trailered to the trails. Options...

WTB build parts for a HD build of the Dana 30 and Dana 35 axle. DELETE Looking for the following Aftermarket carriers for both the 30 and 35 ARB or equivilant locker for both the 30 and 35 Chromoly axles 4:10 ring and pinion gears

I have a 2006 TJ 4.0 automatic trans. I also have a 3.25 lift with 33x12.5 tires. I use this Jeep as a daily driver and would like to have somewhat good gas mileage but I like to have a little bit of power. When I go up the mountain, the Jeep will change gears and then bog down really hard to...

I'm currently in the process of replacing the left front axle shaft U-joint, ball joints, and unit bearing on my '00 TJ. I found recommendations for the ball joints and U-joint here but couldn't find any for the unit bearing. Anyone have a recommendation for a good quality one?

I'm surprised an article like this didn't already exist on the site, especially given the number of people who ask how to identify which axles they have on their Jeep Wrangler TJ. The goal here is to give future TJ owners and new TJ owners a guide on how to identify which axles they have under...

A good friend at work was telling me about some young lads who got themselves into a bit of a pickle out in the woods a week or so ago. The lads dropped a late model Cherokee into a mud hole and buried it pretty well, hydro locking the engine and basically thrashing out the drive train...