clutch

Hello all, I’m reaching the iconic 200k in my 02 Sahara so I believe the my transmission is starting to go as it’s starting to stick, wines, and at times engages gears prematurely. I typically look for upgrades whenever I need to replace a part so my question is what would you guys recommend...

I just purchased an 06 6-speed TJ and had the clutch pedal go limp on my way home. Was able to Jimmy rig it to get home and found that it just needed a $4 bushing to reattach the pedal. Was on my way to work a couple weeks later and had it happen again. This time it didn’t break the bushing...

2001 TJ Sport 4.0 with A/C. Let me provide some background info: After running my Jeep with an electrical fan for the last 7 years, I will be installing a mechanical fan. Long story short, after doing some electrical diagnostics, it would be more trouble than it's worth to continue using the...

Hey guys! Needing some of yall's awesome expertise! So here's what happened. Im out wheeling by where I live, nothing crazy but I go into 4WD Low from 4WD High to get up a hill/mound and after I get over it maybe, 10-20 feet later the 4WD light on my dash goes out. When I notice this I come to a...

Replacing clutch in my 05 LJ 6 speed. Finally got to undoing all the bolts on the bell housing and it won't come apart. I peek around the cover to see if I can pull them apart and I notice this random sleeve/tube sticking through one of the bolt holes. I have triple-checked and all bolts have...

I’ve not been able to find a discussion about this yet so if there is one, my apologies. I have a 03 Wrangler 4.0 and recently I’ve noticed that when engine breaking, primarily in 2nd gear, and slightly in 3rd gear, a metal rattling noise can be heard until the jeeps rpms catch up to speed. It...

Hello All, I've got a 2003 Wrangler. 4.0 5spd. I just recently had the throw-out bearing go. Had a shop replace it along with a new clutch. I asked them to install a new pilot bearing and input shaft bearing as well, but a new noise I am getting now makes me think they did not replace them, or...

So while driving my jeep tj, I suddenly lost the ability to shift gears easily. Ive had to replace the slave cylinder before so I knew the signs. I thought it would be an easy swap but I was wrong. I installed the new cylinder. We were on the last bleed cycle when we heard a loud pop. The...

I have a 2001 Sport, 4.0 manual transmission. Long story short it is about impossible for me to get my trans into first gear. Second is slightly less difficult, and third through fifth are not so easy either. On occasion I can get it to slide right in, but there seems to be no pattern or...

Heyy everyone🥴 I’m new to the forum I have a 99 4Cyl 2.5L (don’t hurt me🤕😂) and I have a question. I went out the other day and started up my 99 Tj (daily driver) drove about a half mile and couldn’t go into 3rd for some reason. The clutch was sticking not letting me shift up or down so I pulled...

I have a 1998 2.5l with the ax-5 manual tranny. SHORT VERSION AT THE BOTTOM So on the 11th of June after not driving my TJ for a week or two and not noticing any problems when I parked it last, I went to start it and drive off after oil started flowing. It went into 1st just fine no resistance...

Hi everyone, I’m a longtime follower of this forum has always been my go to for finding advice on solutions to issues with my TJ. For the first time I’ve really got to reach out for some advice on a problem I’ve been trying to fix for over a year now. Alright so my clutch fork has been...

I have a 1998 wrangler Sahara that stalls occasionally in neutral or when my clutch is in. Typically, this happens when cutting it hard in reverse, after I take it out of reverse, but it can also happen when I am stopped. The RPM’s are very variant at idle, they fluctuate between 7-800 up to...

Okay so I've had this problem for a while now where when I engage and sometimes disengage the clutch, I hear a clunk noise. The sound is coming from the transmission. Could it be the clutch or the actual transmission? Thoughts? We checked every possible thing that could be causing this...

Hi... New member hear I just replaced my transmission for the second time because the first ome 2nd gear syncro went bad (luckily under warranty). I decided to replace clutch too and used the luk kit. After getting everything back together there is a VERY loud whining /gear noise when in 1st...

I have an 04 Tj with the 2.4 and the 5spd, awhile ago I had my clutch done at a shop because my rear main seal had a catastrophic failure and completely doused the clutch in oil, when I went to go pick it up with my dad he told me to drive it home, I turned it on pushed in the clutch and it...

2002 4.0 5psd ~159k miles. Recently and regardless of what gear I'm in or if the engine is on, when I push the clutch to the floor it sometimes hesitates coming back up. It feels and sounds metallic, almost like when you lift off the latch of a yard gate and the latch is worn and gets bound and...

Bought this over a year ago. Ended up not needing it. And of course I waited til I was outside the return window before making that decision. Everything is BRAND FREAKIN NEW, the parts never even left their boxes. Paid over $300, asking $200 OBO plus shipping. Also willing to deliver locally...

Looking for some insights on flywheel condition and cleaning, please. I've just dropped the transmission and removed the clutch. Tons of oil in the bell housing and the flywheel looks scorched! I've spent about an hour trying to get it to a polished state like I've seen in videos and it just...

I'm always seeing 'it's the throw out bearing' yet it was changed, and before even being replaced, the cracking sounds were there. I've seen a video of somebody greasing up the slave cylinder boot or whatever and it goes away, would that be the case? Or if you know other ways to help fix it...