axle

So I broke a passenger axle stub on my Michigan rusted out 98’ 4cyl Manual and luckily I have a friend with a bone yard. Stole a new stub from a 93 hoping they were the same as I read on the Internet... They aren’t. The u joint caps on my old one are bigger. However the part listings everywhere...

Off of a 2006 LJ. Has Revolution shafts, 5.13 gears, Eaton locker, disc brakes, setup for triangulated 4-link. Ready to bolt in. I had to buy them as a pair and only needed the front. Can text or call Sean at Seven02-Six82-4125 for further details. Buyer to arrange pickup/shipping. The axle can...

Pulled my rear Dana 35 when I did an engine swap to upgrade. Jeep has about 130k on the clock. No issues with the rear end at all. Just doing a V8 so I upgraded my rear axle instead of constantly snapping shafts. Axle is complete, still has all the fluids in it. I'm guessing the PO serviced it at...

Is the only difference between the Currie RockJock II and RockJock III axle housings their place of origin? It’s my understanding is the center section of the RockJock III is being made/cast overseas/China while the RockJock II center section being made/cast in USA? Or are there changes in...

Another long shot post, based off some of my recent posting, I may not get what I need. I am looking for a certain measurement on the Spidertrax 3.5 inch Ultimate housing. I would like to know what the measurement is between the axle centerline and the rear most portion of the center section of...

I have a reasonably stock 1998 TJ 2.4L that has a 4 inch lift, and the 29inch tires that I got with it feel like I'm disgracing it, so I've been looking at upgrading. Everything is on a budget, but I'm not trying to make stupid mistakes and cut corners that could come back to bite me, so I've...

Hello all, I have recently bought a 1999 TJ, full stock. I have plans to get a 4in. suspension lift and 33s or 35s. My only thought is the axles, I have factory Dana 30 Front and Dana 35 Rear. My main use for it will be for road trips and daily driving, but I do want to do some light offroading...

I'm trying to find Dana 30 and Dana 35 axle housings. Surprisingly, Davey's Jeeps doesn't carry just the housings. Any recommendations on where to find them besides craigslist and eBay?

Looking for some advice. I have a 99 Sahara on 33's, 4.5" suspension lift, 1" body lift with Dana 35. I was attempting to teach my wife to drive a stick Thursday evening, she kind of held the brake while letting off the clutch, then pop goes the rear diff. (Not her fault or anything, that's...

Hi, Was wondering if I swapped out my rear Dana 30 diff and axles will a Dana 44 diff and axles bolt right in using the rest of the existing stuff on the car? Such as is the brakes, hubs, ball joints, Cs, knuckles, and steering the same? Thanks

Guys I need major help. I have a 2004 Rubicon and I broke an Axle Shaft at the U-Joint. I watched some videos on how to remove it and it looked easy enough. Now that I have it mostly torn apart with the diff cover off mine does not look the same as others. How the heck do I get the axle out? I...

Looking at going to a Dana 44 in my '97 TJ but not finding any off a TJ Rubicon in my budget. I did find one off a JK Rubicon not too far away and a decent price though. How compatible are these 2 axles? I know I could pick one up from various other vehicles for a decent price, but the main...

My dana35 rear diff, pinions, and bearings are all shot in my 98 sahara. To rebuild the axle the parts cost would be roughly 1400 not including labor. I don't think its worth it to put that much into the Dana 35, so I'm looking at swapping it for a Dana 44 or 8.8. What is my best option considering it...

WTB build parts for a HD build of the Dana 30 and Dana 35 axle. DELETE Looking for the following Aftermarket carriers for both the 30 and 35 ARB or equivilant locker for both the 30 and 35 Chromoly axles 4:10 ring and pinion gears

Does anyone know if I have this seal installed correctly? This is a Dana 35 on my 2001 Jeep Wrangler TJ. This started as a brake job and then morphed into a bunch of work on the rear axle. When I removed the old brake drum on the drivers side I found the brakes coated in oil. I replaced the...

I need some advice and insight with my build. I am about a year into research and looking at different ways to build my tj. I want to do it right the first time and i am willing to put some $$$ into it. I want to eventually start crawling on light trails soon but i know its gonna take some...

I have a 2006 TJ 4.0 automatic trans. I also have a 3.25 lift with 33x12.5 tires. I use this Jeep as a daily driver and would like to have somewhat good gas mileage but I like to have a little bit of power. When I go up the mountain, the Jeep will change gears and then bog down really hard to...

New Wrangler TJ owner here. I need help determining what axle type I have. It is a 2005 Wrangler X I did do some research and found that they are most likely Dana 30's but I just want to make sure. Also, what are your suggestions on getting heavier duty axles for off-roading? I've read that the...

The factory Dana 35 rear axle found in most TJ Wranglers is a little on the light side, and if you run larger-than-stock tires, you’re likely looking at an eventual failure. If you want to turn really big tires, wheel abusively, or push gobs of power into your rear axle, you’ll probably want to...

Okay, so after a ton of research and some experiments I finally painted the 1992 Dana 30 high pinion I took out of a trashed MJ. (Re-gear/locker install will start in about two weeks when my last duck is fully dressed and covered.) I won't go into all my reasons, but this is what I finally...