Search results

$34 shipped right now. https://toyotaparts.lakelandtoyota.com/oem-parts/toyota-headlamp-assembly-8111060p70

So it sounds like headlight choices is basically whatever floats your boat kind of deal?

What ate folks landing on alignment specs for someone who has 33” ties on a stock height jeep?

Hmm. I changed from 34 gear to 31 gear. I have the stock 3.73 diff with 33”. The speedo now reads faster by 2-3mph faster than gps vs 34gear that reads 2-3mph slower than gps. Wondering if my diff is actually 3.73 when I got it a couple months ago.

So where does one go to fine the cibie enclosures for our TJs? I’ve googled and can’t find anywhere to buy them? And which cibie e-codes are they?

Does anyone know what the factory nutsert and thumbscrews specs are? Using the diagram part number above, I couldn’t find anything thing that came up mopar or Chrysler.

So I searched the internet to see if the 2000 TJ has an ACC key position. Some people seem to be able to get to it but usually has a button. I need help because mine doesn’t have a button and I cannot turn it towards me after lock (last position to pull out key). Any idea if this isn’t available...

What did you end up doing Jerry? I’m wondering if anyone sells the triangles support piece the bolts to the back of the hinge from the inside to the base of the roll bar.

I have them. They don’t see. Too bad with 33s although I haven’t tried anything else as they came with my jeep.

Yes front is higher than the back but nothing is wet except the back half of the trunk. I check the sides and nothing either.

I’m having a similar issue but under the trunk carpet. I don’t see any trails of water leaking but the carpet is always wet especially after a rain. I have a trunk tray and there’s no water on top of that’s. Need to figure out where it’s coming from and will try to use a hose when it’s not...

I wonder if these would be a perfect replacement for: https://www.amazon.com/dp/B0DWSG2ZZ5?tag=wranglerorg-20

I’m a bit confused. It looks like all the different diagrams I’ve found show the same flow as the OP diagram. Is the bigger one going in and smaller one going out?

Yea I have -19 offset so stocking out a bit for me. I’m hoping an aftermarket bumper maybe with a cut out would allow me to use the stock carrier without the bumper and shorter snubbers. Or a bumper with a carrier swing, not sure if I want that yet though. also for reference. the 120mm bolt...

Honestly I was surprised too. I think it was the combination of having to get an adaptor so it wouldn’t hit the rear bumper and offset is making it sit this far out. Once I get a new rear bumper, I don’t think I’ll need the adaptor anymore. Even with these extended snubbers I do worry about...

The following fits my 33x12.50x15 tires Here are the lengths you'd need to print (PETG): Top Left: 82mm Top Right: 82mm Mid Left: 63mm Mid Right: 63mm Bottom: 71mm (5) ~2mm pads cut to shape M6x1 thread bolt: (2) 120mm and (3) 100mm...

Oh! haha. It's a window vent for the reason in my last post. right now, I crack window half way and use a bunch of magnets to secure a window screen mesh so that there's airflow and keeps the bugs out of the car. However, my current method is kinda janky and not very secure with both bugs to for...

You’re wondering why. I camp in the summer and like to have my dog in the car overnight. I have a crappy solution but would rather have this.

Curious. Has anyone printed something like this for the TJ?

Yeah I got 5 of them and thought id shave them down to look like the original but figured it might be easier to just 3d print them and they would look OEM and can still use the stock snubbers to stack on top.