driveshaft

Hey guys, new to Jeep TJs and this forum. I just did a ton of work on my wife’s 03 wrangler X 5 speed. After putting everything back together, I go to see how the clutch feels and I realize that I’m getting zero power at all. After putting it into 4WD and taking it for a few spins, I noticed...

In the process of rebuilding my rear drive shaft, and noticed a couple of things odd, and had a couple of questions. First, I'm working on an 03 Rubicon, and from Denny's Driveshaft, it looks like the rear DS was calling for a qty of two 5-795x (double u-joint at TC side), and a single 5-793x...

Attempting to change the diff side front drive shaft u-joint, which, to my understanding is a spicer 5-793x (2003 Rubicon). However, the u-joint I pulled out of the driveshaft looks a little odd. The caps were protruding from the drive shaft, and there were no retaining clips. I was able...

I've always noticed a bit of a vibration from my front right wheel. Over the course of the last year I've replaced the axles, ball joints, hub, breaks, and shocks. I have all new tie rods, as well as control arms. Basically the whole front end has been rebuilt over the course of the last year...

Long story short (I typed it all up then it got deleted.) Haven’t driven this puppy in a minute, about a year. Drove it, vibrations out of no where, horrifying noise, pull over, see no driveshaft, uh oh, turn around in 4wd and run home. U-joints failed and driveshaft went flying into a field...

Hi all! I have a broken front driveshaft slip yoke. The websites for my aftermarket part says the part is compatible with LJ’s and 2001-2004 G Cherokees. I have a you-pulll yard near me that has 5 Cherokees that I inspected and look good. But they have a different part number than what is on my...

Hello all! I've had my TJ for about a year now, it is a 2004 wrangler X and its been quite the adventure. For the entire year i've had speed sensitive vibrations that I have tried to get rid of. The past year I have removed the front driveshaft due to damage on the body and replaced the rear...

Okay. As I was trying to find out the source of vibration, I twisted the head off a U joint bolt in the rear yoke. It has a dual cadron driveshaft of an unknown manufacture. My question is, what size yoke and U-joint do I need to get? Is there anyway I can determine the size of the U-joint...

I have a 2005 Rubicon with a 4 inch lift (probably Rough Country). The transfer case is lowered one inch, probably from Rough country too. All from the PO. There is vibration at around 70 MPH. It's done this since I bought it and It seems to be getting worse. I will be checking pinion...

Double carden front driveshaft, rebuilt completely about 1,500 miles ago and has zero damage or issues. Has 1310 ujoints at the attachment points and in the carden. This is setup for a 4” lift on a TJ. Extended length is 39”, collapsed is 35 5/8”. Asking $175 buyer pays shipping. Only reason...

Hi y'all, first time post here and long time lurker, I purchased a real beat up '97 Jeep from the local takuaches last May and I have been fixing it ever since. I've been looking to eliminate vibrations that happen when getting on the freeway starting at 55mph. I recently removed the rear...

Tore down the double cardan joint on my front driveshaft to rebuild it. Unfortunately it looks like I need a new driveshaft… The shaft is badly worn. You can easily feel all of the visible marks. The centering yoke has a small amount of play in the ball and socket joint. The retaining ring...

Gonna attach a photo of my current stock shaft with 4” Currie lift springs on my ‘04 LJ Do you think i need to go with SYE and CV shaft or it seems to me just a proper length stock “style” non cv shaft will be fine due to the not so heavy of my pinion angle i know Tom woods will sell me...

I got some snow in the local mountains a few days back and I took my 99 2.5 up to play around in. It's a pretty mellow dirt road but there were a few puddles and some dust at the bottom where it was dry. When i hit the pavement i started hearing a squeaking noise which i had a good bit of...

Hi, longtime reader and first time poster here. I'm replacing the pinion seal of the Dana 35 rear differential on my 2003 Wrangler X, and I've already removed the 4 bolts on the driveshaft, but it won't budge from there. I've read several threads about it already, and I've tried spraying it...

After a cross country move a month back my automatic '04 6-cylinder started clicking from the front(at one point during the trip, I was traveling on a bumpy forest road and the vehicle simply stopped moving forward on its own. I was in 4WD at the time. I immediately turned off the vehicle and...

I've been running a 4" rough country lift for a year now and unfortunately have been dealing with the driveline vibration since the angles are off. I have an 06 Golden Eagle with the rear dana 44. Which setup should I go with that's cost effective and won't break the bank?

I have a 2002 Jeep Wrangler that has a Pro Comp 2 inch lift with 32 in tires. Ever since the lift and tires there has been a vibration, mainly from my seat and center console, that starts at 50mph and gets worse and worse as I go faster to the point where the vibrations shake the mirrors where I...

So unfortunately, last time I had my front driveshaft rebuilt they put a greasable centering ball in. Shoulda complained about it, but it's been too long now since the rebuild so anyhow.. What's the consensus on how often to grease it? Saw one post saying that 3k miles is the norm, but it would...

Cleaning out part of the garage from the collection of parts I have laying around from my engine swap. Let me know if any of my prices are out of line. Willing to ship and we'll figure out a price to get it to your door. Drive shafts $200/pair: '04 Rubicon front and rear as well as front and...