control arm

Hi sorry if this post is out of place. I’m looking for input on why my upper and lower control arms aren’t lining up to their brackets.(They are lacking roughly an inch) I’ve got the replacement trail arm mounted and have measured from trail arm to trail arm as well as to the body mount nearest...

Hey, hope you all are having a wonderful day. I smashed in my driver side lower control arm mount pretty good. I ordered These from Iron Rock Offroad. Haven’t welded them in yet but some things to keep in mind are that the brackets are not the same for both sides. The left and right side are...

Rear adjustable control arms. Upper are Rubicon Express. Bushings good, no play. Lower Trail Forged control arms. Bushings in good shape, Johnny Joints in good condition. Located in Surprise, AZ Looking for some locals before considering shipping

Has anyone seen this rear upper control arm? If so, do you know where I can get replacement bushings for it? A quick Google hasn't turned up much. Finally - is the rust in the ends a show stopper for replacing the bushings, or can I get a couple of years out of new bushings before...

Pair of (shortarm) Rough Country lower control arms. I installed Johnny Joints the first time the original X-Flex joints needed adjustment. They are freshly disassembled, cleaned and lubricated using Redline CV2. Jam nuts are loosened and ready to set to your desired length. The fixed end...

Need just 1 pair of shortarm lower control arms. Need Currie/Rockjock because they use the smallest tube for the body which will help with my front tire clearance. Single adjustable is fine, condition isn't terribly important ...don't even need the Johnny Joint guts, as long as I have the...

I just got a 99 wrangler all stock except it's sitting on 31s with 15x8 rims, so the wheels stick out from the flares a bit. Since they stick out it wasn't until some time later i noticed the front axle is offset to the driver's side by maybe an inch. I noticed the lower control arm mount on the...

Taken off of my TJ to install Savvy mid arm. It's been awhile since I packaged these up, but I recall that I was missing the mounting hardware for one joint.

Asking $400 shipped. Brand new in box, never been installed. I had planned to install these on my TJ but never got around to it, and now I'm about to list the Jeep for sale. I unwrapped one as an example but left the rest wrapped. I can unwrap all of them and provide additional photos if...

I bought my jeep a couple months ago with a 4” lift that has Pro Comp lower control arms and factory uppers. The bushings have worn out, and from what I have been told they no longer make the replacement bushings. So I’m looking for some recommendations on the best (preferably budget friendly)...

Hey guys, i recently bought a jeep with a long arm kit on it, and i would like to replace the bushings bc they are a little bit worn. however, I don't know what kit the previous owner installed, is there a specific place i should look for a part no.? i didn't see any with a quick look over, but...

I have a pair of JKS upper rear CAs for Jeep TJs. I rebuilt the flex joints after I removed them. So they are functionally like new. New they are over $300/pair. I'm asking $125 shipped domestic.

04 TJ 4.0L, stock as far as I can tell. 30.5” tires. Owned it for 6 months. Skidded out in the snow into a curb with my front passenger wheel/tire. My front passenger lower control arm got pretty bent. The Jeep now pulls to the right and to go straight I have to keep the wheel at 10-10:30...

Long story short; Took the TJ to the shop for an alignment (I know, I know. I could do it myself. But I was in a crunch). ANYWAY, they said they couldn’t do it for 2 reasons. 1) “Track bar is loose” - their explanation was there was play in the tie rod end of the track bar (the driver side...

Full set of used, scratched, dent, grey Core 4 x 4 control arm set. https://www.core4x4.com/product/t2-j-tjlj-cs8/ Pictures spoke by itself Sale is at “it is” They are heavy so local pick up will be best.

Good Day! I recently got my first Jeep, 1997 Wrangler! Dream come true finally, now I need to give it some well deserved TLC. I've been doing little things like fixing blinkers, lights, fluids and such. Along the way I've noticed some things that I need advice on. I've attached a diagram and...

I have a 5 inch lift on my 98 Jeep Wrangler tj. I have recently started to improve my lift so it would drive better. I started with the front lowers control arms. I figured it was time for something else to be added. What should I change next? Rear upper control arms or the front track bar is...

For sale is a used JKS rear track bar with Johnny Joint at adjustable end and axle mounted relocation bracket. This track bar has been great, but now am looking to go triangulated 4 link. The threads on the adjustable sides are nice and clean. Asking $150 obo

Just a quick question, if I upgrade my front lower control arms to a double Johnny Joint set up while leaving my front stock uppers in, will this place undue stress on the upper control arms and control arm brackets? Thank you! Also, does anyone know if the Johnny Joints generally used are...

I know this question had been beaten too many times but I’m having trouble and can not find a solid answer... Going 70mph in sunny hot Florida I hit a pot hole and experienced full on death wobble. Cool. The same day I ordered a new track bar, steering stabilizer, tie rod, and drag link...