Search results

In pretty good condition albeit dusty(which I will clean up before selling) only a few years old, I think 4. I can find the purchase date if needed. It's the 97-02 version. Not sure how different the 02-06 version is. Swapped to a stretch tank so selling this one at a pretty good discount...

Selling my hard top. Doesn't have the wiper but has the wiring for the heater AFAICT. It's been repaints greyish using a sandpaper bed liner(not rubber) It has the vents from the early TJ. It has a crack in one corner. But it's been there as long as I've had it. It has the divot in the...

My original build thread is lost to time. But the winds have shifted anyway. Originally this jeep was my daily driver and so it had to be well mannered(for a short wheel base solid axle vehicle) So now that I have a JT(I can only buy vehicles with a j and a t in the chassis code) for getting...

These are mixed between the every man challenge and the race of the kings. Too lazy to edit them for the next few months so what came from the camera is what I post. Anyone else go and see the fun races. The storm earlier in the week really cut down on the dust Not sure if there's a better...

Just dropped my Jeep off at a local shop. But wondering what could be wrong. Going from a stop on a 45 degree uphill to gas there was a large BANG and then no power. The engine was fine but the Jeep was rolling back. 4hi did nothing, so not an axle shaft Park doesn't hold so likely...

I know I mentioned it forever ago in another thread. This coupler saves many headaches from the basic grease guns you can buy. This coupler spring loads onto your zerk and stays on until you release it. It's pretty cheap but super useful. I've found the latest cheap store brand grease guns to...

I know a lot of us run the JB super short SYE, if your speedo fails mid trip like mine did going to KoH, Napa part CSS1159 is the part to get to replace the hall effect sensor. It's marked as a cam position sensor, but it's the exact fit part and worked for me.

My hard top has this absurd bow in the middle. Is there any way to fix it? Does anyone know what would cause it? The edges where the latches are sit flush but the middle bows up.

Earlier this year I changed my windshield to top gasket and found that the replacement (non Mopar) was very different from the original. The original has what feels like metal inside and is thicker. It also doesn't have the bulb/overhang part in the front. The new one has this bulb/overhang...

For sale are NP231 case. The front output is leaking. The output has a hack n tap SYE. It came off a 32rh and has roughly 230,000 miles. $100 Winch plate, not sure what brand(amirtybilt?). Free Sway bar with 4 inch lift links. Free Stock control arms. Free I'll try to give them a bit of a...

Or maybe an LOLJ? https://www.govplanet.com/for-sale/Automobiles-1997-Jeep-Wrangler-4x4-Limousine-Missouri/4525912 Click if you dare

For anyone with a 32rh transmission, how tight is your throttle valve cable from the throttle to the transmission? My understanding is that there should be no slack at no throttle. Even at max out adjustment my cable still had slack. I'm asking to see if I should go through the effort to...

Changing from this rack to a slightly smaller one. $200 (cheaper than I put on Craigslist) Powder coating in good condition. Generally dusty from use. No bends in tubing. South Bay/Bay area CA Will not fit body lifts without modification Both half's of a Body Armor 4x4 rack for a Jeep TJ...

My driver seat has shredded(like they all seem to) I am looking for medium to good condition seats in Camel tan(tan seat with rainbow ish diamond pattern)I will recushion if needed so long as the cloth isn't torn. I'm in California and am willing to pay reasonable shipping/cost to get it...

I bought my Jeep in 2015 with 151k miles on the clock. I bought it as my first vehicle as a new driver. 1997 sport, so 4.0 with the 32rh with Dana 30/35 and 3.07 gears, soft top, which I would quickly learn was worn out, and a light bar for old round lights. It also had steel bumpers, swing out...

My 97s exhaust is becoming swiss cheese. I'll be heading to an exhaust shop soon to have the whole system replaced south of the manifold. I also remember another user having a eurocar flex pipe put on part to help with the manifold breaking every few years. But what I really am asking is...

Does anyone have a source for a source for a to scale 3D model of a TJ? I've found a few things searching online that aren't quite right. I want to do some designing for a few parts that cardboard aides design just isn't suitable for. Thanks!

I bought an NP231 off Craigslist that the seller bought to put in his Jeep. He chipped the rear output bearing flange when changing bearings. I took the front off to see how much I'll have to rebuild when putting an SYE in and it looks freshly rebuilt from what I can see. $125 off Craigslist.

Until recently it seems like my torque convert hasn't been locking up. What's been done since it has started locking up is: Oil change Transfer case oil change Spark plugs Sat for 2 weeks because of quarentine None of these seem like they would have cause the torque converter to start locking...

Before I undertake any projects to reduce weight on my Jeep, I was wondering what reduction of weight is even noticable from those who have put their Jeep on a diet. How much weight did you reduce and how did it effect drivability/power/handling/sway? What did you do to reduce weight? I am...