Search results

I want to add some switches for accessories in the dash, IE fogs, winch, heated seats, etc. I am the type of person that would much rather use the existing connectors to add my own circuits to keep it clean and organized. So I want to find terminals for the under dash C107, C170 and C202...

Could anyone share some first hand experience with aftermarket motor mounts that utilize OEM Clevite rubber control arm bushings and if there was a significant increase in NVH or if it mostly remained the same? How well have the bushings been holding up. Some examples of these types of mounts...

My 2000 TJ with a Genright 25gal 05-06 tank has a slow fill issue where I can only depress the gas pump trigger halfway, so it won't shut off. With doing a 05-06 tank with different EVAP components as the vehicle it was going on and I also had no instructions on the proper way, I just made up...

How do the factory pumps actually function when the locker switch is engaged? Do they stay on the whole time and are regulated to 5psi or do they turn on and shut off when they hit 5psi and holds pressure? How do they decompress to unlock, does the pump have an integrated valve to vent pressure...

Has anyone replaced the top deck of a JLU soft top? My mom's JL is torn and needs replacing, and I cannot find a good resource on replacing it nor can I find an explanation on what to do with these roller brackets 68430140AA and 68430141AA that we had to order to retrofit a new Mopar top...

Will I have interference issues between exhaust and rear trackbar with a 2.5in exhaust pipe, such as the one from Banks? This will be going on a LJ with a short arm suspension and Genright Safari fuel tank if these matters. This is not going in a stock application, and I will probably have the...

So I had an incident on my honeymoon where a transmission cooling hose popped off and dumped some ATF on the road. I was in the middle of no where Upper Peninsula MI and a gentleman stopped and checked on us and went and grabbed me some ATF from the only gas station around but there was no ATF...

Does anyone know of a crossflow radiator that has the auto trans cooler provisions and puts the coolant inlets and outlets in roughly the same spot as a factory radiator? This is specifically for a GM engine swap, and I have had great success with maintaining temps with an LS swap specific...

I am looking at the idea of using one of the JKS/Metalcloak/RockJock bar pin for the front eliminators and installing under the axle side mount to get closer to a 50/50 bias and getting more uptravel with less bump stop extension. It looks like it would drop the mount .50” to .75” below the...

I am mulling over the idea of installing some Skyjacker M95 shocks that I have lying around into my LJ to make for a softer/smoother ride for an upcoming trip and to use temporarily until I get to cutting the frame to install some custom tuned Foxes. To give some context, in September I am...

Does anyone know if you can replace the 1/2-20 studs in the Spidertrax adapters with the M14 studs that ST uses in their adapters for JL wheels? I am using JL wheels currently and want to keep the lug-nuts the same on all 4 corners but I will be using different adapters front to back. The rear...

Edit: Got 3 sets left. May have more if there are people from the waiting list that end up not purchasing. These seat brackets are designed to lower the seats about 2” in your 97-06 Jeep Wrangler TJs and LJs. These go great with aftermarket seats such as PRP where the aftermarket seat adapter...

Does anyone know on the Rockjock Antirock rod ends with 1/2-20 threads the dimension from the shoulder on the stud end to the back end of the cap?

Does anyone know or can check the rough angle of the power steering pump clocking in relation to the vehicle horizontal axis? I am looking for mainly the angle of the line the mounting holes and/or the pressure line port in relation to the vertical axis of the vehicle. I do not have a 4.0 in...

I am looking at using the Poly Performance towers to extend the front shock mounting points on the front of my LJ, but I was wondering in general how much extra compressed length does such a procedure allow? I understand its a case-by-case basis, I am just trying to see if its realistic to fit...

Does anyone know if Mouser or some other company sells just the connector housing for the 01-06 combo switch (headlight, fogs, etc)? I am aware of the various offerings for the pigtails for $50-75 but I was hoping to just find the connector housing for a lot less and I will just pin them in my...

Doing the U-joints on my drive shaft, I chipped a piece off the slip yoke where the outer lip of the retaining ring groove is. Is this something that needs to be replaced even if the “open” part of the retaining ring is orientated in a way that keeps the retaining part of the ring full coverage...

Has anyone made something like a lawn mower trailer to store a hardtop on and be able to move around with a rider mover? I was looking for inspiration for something like this so I can stick my LJ hardtop in the back corner of my property since I do not have any space inside or on the ceiling of...

Does anyone know the difference in length between the fuel hardlines of a LJ and TJ? I am looking to see if a company that I bought a set of fuel lines in the past from for my TJ could make a set for the LJ. I figured the only real difference is the straight section is longer between the 2...

I was at a car wash recently and a lot of water poured in from the top section of the rear window. Is there a way to seal up the window to hardtop better? I adjusted with mounts on the window and do have a new seal on the inner lip and all of it helped a little but has anyone used something...