Recent content by Tinnitus_Z

Hello again, I've been getting the P0340 and P1391 codes recently. Last week the starter solenoid went out, and I had to buy a whole new starter with it included since they don't sell the solenoid separately. After I replaced the starter and cleared the codes, only the P0340 code came back, and...

The only filament allowed to use at the 3D printers at my library is corn based PLA. Online it says it starts to melt around 170 and the temp of the printer has to be 190 before printing. I don’t know how hot it will get in there since my heat doesn’t fully work anyways. Temperature coming out...

Update: I have installed the bracket/arm piece and it fully works and turns the door when changing the air control between blower and defrost. That STL file that I posted, and if you 3D printed it, will work in place of that arm piece if it was broken like mine. It did have trouble at first...

I've tried my best to recreate the bracket/arm in Sketchup from scratch and 3D printed it. Here are the pictures of the actual piece with a ton of glue, and the 3D printed piece. This did take a while and the file is the best resulting 3D print. Here is the STL file, although it may need to be...

Alright, I'll go check while doing the quick center to side turns instead of the long full side to side turns. As for the tire balance, I am most likely getting new rims and tires in the next few months so hopefully all four wheels shouuld be balanced.

Hello again, here's a video of my front-end track bar in question. When I turn my wheels to the right, there is a loud popping noise coming from the passenger side. Took this video and noticed that the track bar is moving in the bracket and "popping" when I turn to the right, and this is very...

I found an old photo of when I got the pieces out. The part on the left breaks into 2 pieces, and I've lost some tiny fragments that were holding everything together. I'll have to wait until I bring it back to where I currently live before I can Jerry rig it. Would you recommend just a coarse...

I have not fixed it yet. I’ve contacted the Jeep dealerships part specialist on October 5th and still haven’t gotten a reply. Probably isn’t even worth trying to talk to the dealership though. I’m currently away from home at college and when I get back for thanksgiving break, I’ll grab the...

Hello, sorry if this is similar to my previous post, but I decided to take some pictures of what I am talking about with the heat blend door. I have verified that all the actuators and electrical motors work, all the vacuum lines are good and there are no leaks, but I cannot get defrost working...

So the second picture shows the arm that broke. One side is supposed to clip into the metal piece of the actuator, and the other part of that plastic arm plugs into the hole in the heat box in the last picture. (The hole directly to the right of the metal piece in the last picture to be more...

Hello all, after taking apart my dashboard to find the issue with my heat, I accidentally broke the arm that connects to the bottom driver side HVAC actuator. I have a 2002 4.0L if that is needed to help. I have fixed my heating issue and I now get 125-130 degrees when the heat is on...

Just found out it was a Walker O2 sensor, would a wrong O2 sensor cause the P1391 code? It started showing up after I replaced the O2 sensors.

Thanks, I'll check those out

Well I installed two different O2 sensors. My dad accidentally broke Bank 2 Sensor 1 a couple of days ago so he had to buy one immediately and got the only one remaining from Autozone, most likely Bosch since they only carry that at my location for some reason. I bought and installed the NTK...

Hello, I am new to forums and I don't really know how these work too well so I may be asking wrong. Anyway, after replacing O2 sensor 1 (bank 1 and bank 2) today, I now got the code P1391 for the crankshaft position sensor or camshaft position sensor. I have a 2002 manual 4.0 TJ and I already...